Réglages températures OWA (PS et ABS)

[filament]
name = PS rose OWA
diameter = 1.75
multiplierPercent = 100
printingTemperature = 245
enableCooling = True
bedTemperature = 90
fanSpeedMin = 70
fanSpeedMax = 100
minimalLayerTime = 5

[print]
name = mes reglages mks56
defaultQuality = yf6DYT1K3mcoGBgNQPIiy5j6Vx753qiB
travelSpeedMin = 150
travelSpeedMax = 150
firstLayerSpeedMin = 15
firstLayerSpeedMax = 15
infillSpeedMin = 60
infillSpeedMax = 100
skinSpeedMin = 30
skinSpeedMax = 60
infillType = 1
innerPerimeterMin = 40
innerPerimeterMax = 80
outerPerimeterMin = 30
outerPerimeterMax = 60
printSpeedMin = 40
printSpeedMax = 60
nozzleDiameter = 0.4
gcodeFlavour = 0
retractionCombing = True
combing = 1
multiVolumeOverlap = 0
cutOffObjectBottom = 0
shellThickness = 0.8
infillTopBottomThickness = 0.8
infillDensityPercent = 20
supportType = 1
platformAdhesion = 0
dualExtrusion = 0
wipeAndPrimeTower = True
oozeShield = False
enableRetraction = True
retractionSpeed = 35
retractionDistance = 2
multiExtruderSwitchAmount = 16
startGCode = «  » »
; Default start code
G28 ; Home extruder
G1 Z15 F{Z_TRAVEL_SPEED}
M107 ; Turn off fan
G90 ; Absolute positioning
M82 ; Extruder in absolute mode
{IF_BED}M190 S{BED}
; Activate all used extruder
{IF_EXT0}M104 T0 S{TEMP0}
G92 E0 ; Reset extruder position
; Wait for all used extruders to reach temperature
{IF_EXT0}M109 T0 S{TEMP0}
«  » »
endGCode = «  » »
; Default end code
; Disable all extruder
G91 ; Relative positioning
{IF_EXT0}T0
{IF_EXT0}G1 E-1 ; Reduce filament pressure
M104 T0 S0

M107 ; Turn off fan

G28; Home extruder

G90 ; Absolute positioning
G92 E0 ; Reset extruder position
M140 S0 ; Disable heated bed
M84 ; Turn steppers off
«  » »
preSwitchExtruderCode = «  » »
T0
G92 E0
T1
G92 E0
«  » »
postSwitchExtruderCode =
wipeAndPrimeTowerVolume = 15
retractionMinimumTravel = 1.5
minimumExtrusionBeforeRetract = 0.02
zhop = 0
skirtLineCount = 2
skirtDistance = 3
skirtMinimumLength = 150
solidInfillTop = True
solidInfillBottom = True
infillOverlapPercent = 15
supportStructureType = 0
supportOverhang = 60
supportFillPercent = 15
supportDistanceXY = 0.7
supportDistanceZ = 0.2
supportExtruder = -1
spiralizeOuterContour = False
brimWidth = 5
raftExtraMargin = 5
raftLineSpacing = 1
raftBaseThickness = 0.3
raftBaseWidth = 0.7
raftInterfaceThickness = 0.2
raftInterfaceLineWidth = 0.2
raftAirGap = 0
raftAirGapLayer0 = 0
raftSurfaceLayer = 1
fixCombineEverythingA = True
fixCombineEverythingB = False
fixKeepOpenFaces = False
fixExtensiveStitching = False
fanFullAtHeight = 0.5
perimeterBeforeInfill = True
minimumSpeed = 10
coolHeadLift = True
numQuality = 5
[quality_0]
name = 0.1 mm
signature = m2lfZPFLfw8o2YihtNOLfBxwgp4wz8Tx
layerHeight = 0.1
layer0widthPercent = 100
firstLayerHeight = 0.2
[quality_1]
name = 0.15 mm
signature = syZgWL8BNxOtSFWOyEFfhXXlIKwciPHP
layerHeight = 0.15
layer0widthPercent = 100
firstLayerHeight = 0.2
[quality_2]
name = 0.2 mm
signature = JucECOwACBDYChw6CP4sI3gZSSeD8cHW
layerHeight = 0.2
layer0widthPercent = 100
firstLayerHeight = 0.25
[quality_3]
name = 0.25 mm
signature = yf6DYT1K3mcoGBgNQPIiy5j6Vx753qiB
layerHeight = 0.25
layer0widthPercent = 100
firstLayerHeight = 0.3
[quality_4]
name = 0.3 mm
signature = cbvz1hJw2Z3atKbTKRFl1GpqTLovpGKH
layerHeight = 0.3
layer0widthPercent = 100
firstLayerHeight = 0.3
[quality_5]
name = 0.35 mm
signature = w2xLIjilgBFmR1zavsSVGi9ei57cm3cG
layerHeight = 0.3
layer0widthPercent = 100
firstLayerHeight = 0.35