Réglages températures OWA (PS et ABS)

Revision for “Réglages températures OWA (PS et ABS)” created on 14 juin 2018 à 0 h 08 min

Titre
Réglages températures OWA (PS et ABS)
Contenu
[filament] name = PS rose OWA diameter = 1.75 multiplierPercent = 100 printingTemperature = 245 enableCooling = True bedTemperature = 90 fanSpeedMin = 70 fanSpeedMax = 100 minimalLayerTime = 5     [print] name = mes reglages mks56 defaultQuality = yf6DYT1K3mcoGBgNQPIiy5j6Vx753qiB travelSpeedMin = 150 travelSpeedMax = 150 firstLayerSpeedMin = 15 firstLayerSpeedMax = 15 infillSpeedMin = 60 infillSpeedMax = 100 skinSpeedMin = 30 skinSpeedMax = 60 infillType = 1 innerPerimeterMin = 40 innerPerimeterMax = 80 outerPerimeterMin = 30 outerPerimeterMax = 60 printSpeedMin = 40 printSpeedMax = 60 nozzleDiameter = 0.4 gcodeFlavour = 0 retractionCombing = True combing = 1 multiVolumeOverlap = 0 cutOffObjectBottom = 0 shellThickness = 0.8 infillTopBottomThickness = 0.8 infillDensityPercent = 20 supportType = 1 platformAdhesion = 0 dualExtrusion = 0 wipeAndPrimeTower = True oozeShield = False enableRetraction = True retractionSpeed = 35 retractionDistance = 2 multiExtruderSwitchAmount = 16 startGCode = """ ; Default start code G28 ; Home extruder G1 Z15 F{Z_TRAVEL_SPEED} M107 ; Turn off fan G90 ; Absolute positioning M82 ; Extruder in absolute mode {IF_BED}M190 S{BED} ; Activate all used extruder {IF_EXT0}M104 T0 S{TEMP0} G92 E0 ; Reset extruder position ; Wait for all used extruders to reach temperature {IF_EXT0}M109 T0 S{TEMP0} """ endGCode = """ ; Default end code ; Disable all extruder G91 ; Relative positioning {IF_EXT0}T0 {IF_EXT0}G1 E-1 ; Reduce filament pressure M104 T0 S0 M107 ; Turn off fan G28; Home extruder G90 ; Absolute positioning G92 E0 ; Reset extruder position M140 S0 ; Disable heated bed M84 ; Turn steppers off """ preSwitchExtruderCode = """ T0 G92 E0 T1 G92 E0 """ postSwitchExtruderCode = wipeAndPrimeTowerVolume = 15 retractionMinimumTravel = 1.5 minimumExtrusionBeforeRetract = 0.02 zhop = 0 skirtLineCount = 2 skirtDistance = 3 skirtMinimumLength = 150 solidInfillTop = True solidInfillBottom = True infillOverlapPercent = 15 supportStructureType = 0 supportOverhang = 60 supportFillPercent = 15 supportDistanceXY = 0.7 supportDistanceZ = 0.2 supportExtruder = -1 spiralizeOuterContour = False brimWidth = 5 raftExtraMargin = 5 raftLineSpacing = 1 raftBaseThickness = 0.3 raftBaseWidth = 0.7 raftInterfaceThickness = 0.2 raftInterfaceLineWidth = 0.2 raftAirGap = 0 raftAirGapLayer0 = 0 raftSurfaceLayer = 1 fixCombineEverythingA = True fixCombineEverythingB = False fixKeepOpenFaces = False fixExtensiveStitching = False fanFullAtHeight = 0.5 perimeterBeforeInfill = True minimumSpeed = 10 coolHeadLift = True numQuality = 5 [quality_0] name = 0.1 mm signature = m2lfZPFLfw8o2YihtNOLfBxwgp4wz8Tx layerHeight = 0.1 layer0widthPercent = 100 firstLayerHeight = 0.2 [quality_1] name = 0.15 mm signature = syZgWL8BNxOtSFWOyEFfhXXlIKwciPHP layerHeight = 0.15 layer0widthPercent = 100 firstLayerHeight = 0.2 [quality_2] name = 0.2 mm signature = JucECOwACBDYChw6CP4sI3gZSSeD8cHW layerHeight = 0.2 layer0widthPercent = 100 firstLayerHeight = 0.25 [quality_3] name = 0.25 mm signature = yf6DYT1K3mcoGBgNQPIiy5j6Vx753qiB layerHeight = 0.25 layer0widthPercent = 100 firstLayerHeight = 0.3 [quality_4] name = 0.3 mm signature = cbvz1hJw2Z3atKbTKRFl1GpqTLovpGKH layerHeight = 0.3 layer0widthPercent = 100 firstLayerHeight = 0.3 [quality_5] name = 0.35 mm signature = w2xLIjilgBFmR1zavsSVGi9ei57cm3cG layerHeight = 0.3 layer0widthPercent = 100 firstLayerHeight = 0.35
Extrait


OldNewDate CreatedAuthorActions
14 juin 2018 à 0 h 08 min Christophe S